An investigation of the influence of sulphide inclusions on tool-wear in high speed milling of tool steels

G. Poulachon; M. Dessoly; C. Le Calvez; J. L. Lebrun; V. Prunet; I. S. Jawahir

doi:10.1016/S0043-1648(01)00614-7

An investigation of the influence of sulphide inclusions on tool-wear in high speed milling of tool steels

G. Poulachon, M. Dessoly, C. Le Calvez, J. L. Lebrun, V. Prunet, I. S. Jawahir

Research output: Contribution to journal › Article › peer-review

15 Scopus citations

Abstract

Experimental results have shown that the machinability of tool steels, in term of tool-life, is increased with sulphides addition. It seems that this increase depends on cutting speed, probably due to the existence of an adherent layer of manganese sulphides (MnS) frequently observed in turning. Previous studies on the same materials have shown that at high cutting speeds, the action of sulphur disappears. The choice of the best cutting parameters is presented in detail according to the tool-work material pair method. Experimental design has been used to determine the tool-wear rate and to discuss the effect of each influencing factor and interaction. During the progressive tool-wear, rake face investigations to study the influence of sulphide inclusions have been performed using scanning electron microscopy (SEM) techniques.

Original language	English
Pages (from-to)	334-343
Number of pages	10
Journal	Wear
Volume	250
Issue number	1-12
DOIs	https://doi.org/10.1016/S0043-1648(01)00614-7
State	Published - Oct 2001

Keywords

Adherent layer
High speed milling
Sulphide inclusions
Tool-wear

ASJC Scopus subject areas

Condensed Matter Physics
Mechanics of Materials
Surfaces and Interfaces
Surfaces, Coatings and Films
Materials Chemistry

Access to Document

10.1016/S0043-1648(01)00614-7

Cite this

@article{0c67df78587e4f53989f9f50d51ed72b,

title = "An investigation of the influence of sulphide inclusions on tool-wear in high speed milling of tool steels",

abstract = "Experimental results have shown that the machinability of tool steels, in term of tool-life, is increased with sulphides addition. It seems that this increase depends on cutting speed, probably due to the existence of an adherent layer of manganese sulphides (MnS) frequently observed in turning. Previous studies on the same materials have shown that at high cutting speeds, the action of sulphur disappears. The choice of the best cutting parameters is presented in detail according to the tool-work material pair method. Experimental design has been used to determine the tool-wear rate and to discuss the effect of each influencing factor and interaction. During the progressive tool-wear, rake face investigations to study the influence of sulphide inclusions have been performed using scanning electron microscopy (SEM) techniques.",

keywords = "Adherent layer, High speed milling, Sulphide inclusions, Tool-wear",

author = "G. Poulachon and M. Dessoly and {Le Calvez}, C. and Lebrun, {J. L.} and V. Prunet and Jawahir, {I. S.}",

year = "2001",

month = oct,

doi = "10.1016/S0043-1648(01)00614-7",

language = "English",

volume = "250",

pages = "334--343",

number = "1-12",

}

TY - JOUR

T1 - An investigation of the influence of sulphide inclusions on tool-wear in high speed milling of tool steels

AU - Poulachon, G.

AU - Dessoly, M.

AU - Le Calvez, C.

AU - Lebrun, J. L.

AU - Prunet, V.

AU - Jawahir, I. S.

PY - 2001/10

Y1 - 2001/10

N2 - Experimental results have shown that the machinability of tool steels, in term of tool-life, is increased with sulphides addition. It seems that this increase depends on cutting speed, probably due to the existence of an adherent layer of manganese sulphides (MnS) frequently observed in turning. Previous studies on the same materials have shown that at high cutting speeds, the action of sulphur disappears. The choice of the best cutting parameters is presented in detail according to the tool-work material pair method. Experimental design has been used to determine the tool-wear rate and to discuss the effect of each influencing factor and interaction. During the progressive tool-wear, rake face investigations to study the influence of sulphide inclusions have been performed using scanning electron microscopy (SEM) techniques.

AB - Experimental results have shown that the machinability of tool steels, in term of tool-life, is increased with sulphides addition. It seems that this increase depends on cutting speed, probably due to the existence of an adherent layer of manganese sulphides (MnS) frequently observed in turning. Previous studies on the same materials have shown that at high cutting speeds, the action of sulphur disappears. The choice of the best cutting parameters is presented in detail according to the tool-work material pair method. Experimental design has been used to determine the tool-wear rate and to discuss the effect of each influencing factor and interaction. During the progressive tool-wear, rake face investigations to study the influence of sulphide inclusions have been performed using scanning electron microscopy (SEM) techniques.

KW - Adherent layer

KW - High speed milling

KW - Sulphide inclusions

KW - Tool-wear

UR - http://www.scopus.com/inward/record.url?scp=0142179429&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0142179429&partnerID=8YFLogxK

U2 - 10.1016/S0043-1648(01)00614-7

DO - 10.1016/S0043-1648(01)00614-7

M3 - Article

AN - SCOPUS:0142179429

SN - 0043-1648

VL - 250

SP - 334

EP - 343

JO - Wear

JF - Wear

IS - 1-12

ER -

An investigation of the influence of sulphide inclusions on tool-wear in high speed milling of tool steels

Abstract

Keywords

ASJC Scopus subject areas

Access to Document

Other files and links

Fingerprint

Cite this