Ir directamente a la navegación principal Ir directamente a la búsqueda Ir directamente al contenido principal

Eco-friendly solvents and their mixture for the fabrication of polysulfone ultrafiltration membranes: An investigation of doctor blade and slot die casting methods

  • Xiaobo Dong
  • , Tae J. Jeong
  • , Eric Kline
  • , Lillian Banks
  • , Eric Grulke
  • , Tequila Harris
  • , Isabel C. Escobar

Producción científica: Article › revisión exhaustiva

56 Citas (Scopus)

Resumen

Nonsolvent induced phase separation has been widely used to fabricate polymeric membranes. Common solvents, such as dimethylacetamide (DMAc) and N-Methyl-2-pyrrolidone (NMP), are toxic and not environmentally friendly; therefore, eco-friendly alternatives are needed. Eco-friendly solvents, such as Rhodiasolv® PolarClean (PolarClean) and γ-valerolactone (GVL), have been investigated to replace DMAc and NMP at the laboratory scale; however, not extensively at the production scale. In this work, the feasibility of fabricating polysulfone (PSf) ultrafiltration membranes using eco-friendly solvents at laboratory and production scales is investigated. First, it was determined that the addition of GVL to dope solutions of PolarClean could reduce the original preparation time at a rotation speed of 450 RPM by two-thirds, and by three-quarters at 600 RPM. Furthermore, dope solutions exhibit Newtonian fluid behavior. Doctor blade extrusion and a roll-to-roll (R2R) system integrated with slot die casting are used to fabricate the PSf ultrafiltration membranes at laboratory and production scales, respectively, and the resulting membranes are compared structurally, morphologically and operationally. The chemical structure of membranes is not affected by the use of different solvents or by the differences in fabrication scale. On the other hand, cross-sectional images show that the structures of the membranes are different, most likely due to differences in diffusion rates between the different solvents/co-solvents into the nonsolvent, water. Furthermore, it has been observed that the roughness values of the membranes relative to the fabrication process is different, possibly due to differences in the required evaporation time. All membranes display similar operational parameters, i.e., flux decline, permeability and recovery, during bovine serum albumin (BSA) filtration. Therefore, this study shows that PSf membranes fabricated using eco-friendly solvent mixtures are comparable to traditional membranes, cast using petroleum-derived solvents, and are scalable using slot die casting on a R2R.

Idioma originalEnglish
Número de artículo118510
PublicaciónJournal of Membrane Science
Volumen614
DOI
EstadoPublished - nov 15 2020

Nota bibliográfica

Publisher Copyright:
© 2020 Elsevier B.V.

Financiación

The crossflow filtration shows that the membranes cast using the slot die technique perform better or have at least equivalent flux to those cast using the doctor blade. However, it is observed that all the membranes cast using the doctor blade show higher BSA rejections than the slot die membranes, mostly due to the sponge-like support layers in the cross-sectional structures of the membranes, which were discussed previously (Fig. 9).The authors acknowledge that this work was supported by the National Science Foundation under Cooperative Agreement (grant number 1355438) and by the NSF KY EPSCoR Program. The authors acknowledge Solvay Novecare for providing PolarClean, Dr. Matthew Weisenburger in Center of Applied Energy Research, University of Kentucky, for his help with rheometer, Professor Fuqian Yang for his help on AFM. The authors also want to acknowledge the contribution Dr. Eric Grulke gave in this project. He will be missed. The authors acknowledge that this work was supported by the National Science Foundation under Cooperative Agreement (grant number 1355438 ) and by the NSF KY EPSCoR Program. The authors acknowledge Solvay Novecare for providing PolarClean, Dr. Matthew Weisenburger in Center of Applied Energy Research, University of Kentucky, for his help with rheometer, Professor Fuqian Yang for his help on AFM.

FinanciadoresNúmero del financiador
Solvay Novecare
National Science Foundation Arctic Social Science Program1355438

    ASJC Scopus subject areas

    • Biochemistry
    • General Materials Science
    • Physical and Theoretical Chemistry
    • Filtration and Separation

    Huella

    Profundice en los temas de investigación de 'Eco-friendly solvents and their mixture for the fabrication of polysulfone ultrafiltration membranes: An investigation of doctor blade and slot die casting methods'. En conjunto forman una huella única.

    Citar esto